Installation Instructions

[one_half]

Emblem Inlays

15-17 ATS/ATS-V

13-14 ATS/ATS-V[/one_half][one_half]

Side Marker Inlays

15-17 ATS/ATS-V

13-14 ATS

*Smoke/Light Smoke Tint*[/one_half]

[one_half]

Decals

All Decals[/one_half][one_half][/one_half]

 

 

 

15-17 ATS/ATS-V

Whats Needed:
isopropyl alcohol or ammonia free glass cleaner
When installing the inlays please:
1. Clean the emblems with alcohol or ammonia free glass cleaner
2. Ensure the area is dry and lint free *if any cleaner is left the inlay will not stick!
3. Start laying each panel by aligning the top inside corner, once aligned hold with once finger and lay down the rest moving outward with your other hand.
4. Use a business car or something thin to tuck the ends over.
5. once installed, apply pressure to each panel ensuring you hit the corners and the slightly folded edges. This pressure ensures the adhesive is activated and the inlay will last.

This film is 3m 1080 film which is 100% repositionable. If you are not 100% straight, peel and reapply. Please keep in mind this film will stretch so be mindful if this step is needed.

 

13-14 ATS Emblem

What’s needed for installation:
1. isopropyl alcohol or ammonia free glass cleaner
2. A razor knife, or tweezers
3. Patience, this is the most tedious inlay there is.

When installing the inlays:
1. Clean the emblems with alcohol or glass cleaner
2. Ensure the area is dry and lint free
3. Peel one panel at a time off the backing paper and attach to the tweezers or razor knife
3. Start laying each panel by aligning the deepest point of the panel and laying the vinyl down and outward.
5. Once installed, apply pressure to each panel ensuring you hit the corners. This pressure ensures the adhesive is activated and the inlay will last.

*This film is 3m 1080 film which is 100% repositionable. If you are not 100% straight, peel and reapply. Please keep in mind this film will stretch so be mindful and pull lightly if this step is needed.

 

Side Marker 

What’s needed for installation:
isopropyl alcohol or ammonia free glass cleaner

*These are cut 1/16 larger than the marker to allow 1/32in to tuck in around the light.

*This film is 3m 1080 film which is 100% repositionable. If you are not 100% straight, peel and reapply. Please keep in mind this film will stretch so be mindful and pull lightly if this step is needed.

When installing the inlays:
1. Clean the Side Markers with alcohol or glass cleaner- Ensure the edges of the marker are clean as well
2. Ensure the area is dry and lint free
3. Start laying each panel by aligning the vinyl on the bottom front of the marker. While holding the bottom front corner, slowly lay the remaining vinyl upward.
5. Once aligned, apply pressure to each marker ensuring you hit the corners. This pressure ensures the adhesive is activated and the inlay will last.

 

Side Marker Tint

What’s needed for installation:
isopropyl alcohol or ammonia free glass cleaner
Spray Bottle with 1 drop of mild soap (like baby shampoo) per 12oz.
Sponge or squeegee
65 degrees or warmer temperature

*These are cut 1/16 larger than the marker to allow 1/32in overlay around the light.

*This is a tint film so you are only able to move the pieces when they are wet. If they dry, do not attempt to move them as the adhesive backing will be ruined.

When installing the inlays:
1. Clean the Side Markers with alcohol or glass cleaner- Ensure the edges of the marker are clean as well
2. Ensure the area is dry and lint free
3. Spray a liberal amount of water solution to the side marker
4. Peel one inlay from the sheet and spray the back/adhesive side of the tint with water solution
5. Start laying each panel by aligning the vinyl on the bottom front of the marker. While holding the bottom front corner, slowly lay the remaining vinyl upward.
6. Spray the other side of the inlay while its on the car with the water solution and use the squeegee or wet sponge in an outward direction to push the water solution and bubbles out from under the film (the water solution will allow you to work the bubbles out without scratching the outside of the film)

*Please let the tint dry for at least 12 hours before driving the car. any small bubbles that remain will evaporate over the next 7-21 days depending on temperature.


 
 

Decal

What’s needed for installation:
isopropyl alcohol or ammonia free glass cleaner

1. Clean the area with alcohol or ammonia free glass cleaner
2. Peel the backing paper off the decal. If the sticker clings to the backing, slowly replace the paper backing and repeat 3. Place the decal onto the surface and rub it in place firmly with a squeegee or credit card.
4. Slowly peel the transfer tape off at a 45 degree angle. Be careful not to pull the sticker off the surface. If the decal pulls away from the surface repeat Step 3.
5. Once installed, apply pressure to each panel ensuring you hit the corners and the slightly folded edges. This pressure ensures the adhesive is activated and the inlay will last.